Black & Decker KS600E Manuel d'instructions télécharger pdf (Page 13)

Cut line blower (fig. E)

To aid visibility when cutting, your jigsaw is equipped with

a cut line blower(13) which willkeep thework area clearof

dust as you saw.

Use

Adjusting the shoe plate for bevel cuts (fig. F)

The shoe plate can be set to make either a straight cut or a

left or right bevel cut at an angle of 45°.

Pull the shoe plate (4) forward, rotate the shoe plate (4) to

the left or right and push it back into the 45° location.

Push thebladesupportroller(5)forwarduntil it touchesthe

saw blade (7).

Tighten the two screws (8).

To reset the shoe plate for straight cuts:

Loosen the screws (8).

Pull the shoe plate (4) forward, rotate to the centre and

push it back into the 0° location.

Push thebladesupportroller(5)forwarduntil it touchesthe

saw blade (7).

Tighten the two screws (8).

Variable speed control

The tool has a variable speed On/Off switch (1). The

operating speed depends on how far you press the switch.

Use a high speed for wood, medium speed for aluminium and

PVC and low speed for metals other than aluminium.

Switching on and off

To switch the tool on, press the on/off switch (1).

To switch the tool off, release the on/off switch (1).

For continuous operation, press the lock-on button (2) and

release the on/off switch (1).

To switch the tool off when in continuous operation, press

and release the on/off switch (1).

Sawing

Hold the tool firmly with both hands while cutting.

The shoe should be held firmly against the material being

cut. This will help prevent the saw from jumping, reduce

vibration and minimise blade breakage.

Let the blade run freely for a few seconds before starting

the cut.

Apply only a gentle pressureto the tool while performing

the cut.

Hints for optimum use

Sawing laminates

When cutting laminates splintering may occur which can

damage the presentation surface. The most common saw

blades cut on the upward stroke, therefore if the shoe plate

is sitting on the presentation surface either use a saw blade

that cuts on the downward stroke or:

Use a fine-tooth saw blade.

Saw from the back surface of the workpiece.

Clamp a piece of scrap wood or hardboard to both sides of

the workpiece to minimise splintering, and saw through

this sandwich.

Sawing metal

Be aware that sawing metal takes much more time than

sawing wood.

Use a saw blade suitable for sawing metal.

When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cutthrough

this sandwich.

Spread a film of oil along the intended line of cut.

Maintenance

Your Black & Decker tool has been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper care

and regular cleaning.

Warning! Before performing any maintenance or cleaning,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped.

Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner. Never let

any liquid getinsidethetool andnever immerseany part of

the tool into liquid

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you find one day that your appliance

needs replacement, or if it is of no further use to

you, think of the protection of the environment.

Black & Decker repair agents will accept old

Black & Decker tools and ensure that they are

disposed of in an environmentally safe way.

Separate collection of used products and

packaging allows materials to be recycled and

used again. Re-use of recycled materials helps

prevent environmental pollution and reduces the

demand for raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

ENGLISH

1 2 ... 8 9 10 11 12 13 14

Commentaires sur ces manuels

Pas de commentaire

Black & Decker KS600E Manuel d'instructions Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Scies à chaîne sans fil Black & Decker KS600E