JXG4604A
Owner’s Manual
18
If the inside surface of the grill lid
has the appearance of peeling paint, baked on grease has turned to carbon and is flaking off.
Clean thoroughly
with a strong solution of detergent
and hot
water.
Rinse
with
water and
allow it to completely dry.
Interior of grill bottom – Remove residue using brush, scraper and/or cleaning pad.
Wash with a dishwashing detergent and hot
water solution.
Rinse with
water and let dry.
Cooking Grates –
The porcelain grates have a glass-like
composition that should be
handled
with care. Use a
mild dishwashing
detergent or baking soda and hot
water solution. Non-abrasive scouring powder can be used
on stubborn stains. Rinse
with
water.
Heat Plates
–
Clean
residue with wire brush
and wash with
soapy water.
Rinse with water.
Grease Cup –
Periodically empty the grease cup
and clean
with
a
dishwashing detergent and hot
water solution.
Cleaning the Burner Assembly
1.
Turn gas off
at the control
knobs and propane tank.
2.
Remove cooking grates and heat
plate.
3.
Remove
grease
cup.
4.
Remove burner
by unscrewing nut from beneath
burner
“foot” using a screwdriver and pliers.
5.
Lift burner up and away
from the gas
valve orifice.
6.
Clean inlet (venturi tube) of burner
with small bottle brush or compressed air.
7.
Remove all food residue and dirt on outside of
burner surface.
8.
Clean any clogged ports
with a stiff
wire
(such as an opened paper clip).
9.
Inspect burner for damage
(cracks or holes). If damage is found, replace
with a new burner. Reinstall burner. Make certain the
gas valve orifices are correctly
positioned, pointing straight into burner inlet
(venturi tube).
Also, check position of spark
electrode.
T
oubleshootin
P
oblem
Possible Cause P
evention
Cure
B
urner
will
not
light
using
knobs
or
i
niter.
Wires and/or
electrode
covere
with cookin
residue.
Clean
wire
and
/or
electrode
wit
rubbin
alcohol.
Electrode and burners are wet. Wi
e dr
wi
h
clo
h.
Electrode cracked or broken
s
arks at crack.
Replace elec
rode.
Burner
will
not
light
using
a
match.
Wire
loose
or
disconnected.
Reconnect
wire
or
replace
electrode/wire
assembly.
No
gas
flow.
Check
if
propane
tank
is
empty.
If
empty,
replace
or
refill.
If
propane tan
is
not
empty,
refer
to
Excessive flow
safety
valve
reset
procedure
on
page
16.
Coupling
nut
and
regulator
not
ull
connected.
Turn
the
coupling
nut
about
one-hal
to
three
quarters
additional
turn
unti
solid
stop.
Tighten
by
hand
ONLY
do not use
ools.
Obs
ruc
ion o
gas
low. Clear burner
tubes.
Check
or bent
or
kinked
hose.
Disengagement o
burner to valve. Reengage
burner
and
valve.
Spider
webs
or
insect
nest
in
venturi.
Clean venturi.
Burner ports clo
ed or blocked. Clean burner
ports.
(32 pages)
(8 pages)
(24 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels