Black & Decker KG725 Fiche technique télécharger pdf (Page 5)

ENGLISH

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

Additional safety instructions for angle grinders

Read the instruction manual before use.

Wear safety glasses or goggles when operating this

tool.

Wear ear protection when operating this tool.

◆ Always use eye and ear protection when operating this

tool.

◆ Personal protective equipment such as dust mask, gloves,

helmet and apron should be worn.

◆ Do not cut or grind light metal with a magnesium content

exceeding 80%, since this type of metal is flammable.

◆ Only use grinding and cutting discs and other accessories

recommended in this manual.

◆ Make sure that the maximum speed of the grinding or

cutting disc exceeds the no-load speed of the tool.

◆ Do not use grinding and cutting discs that do not conform

to the dimensions stated in the technical data. Do not use

separate reducing bushings or adapters or make

unauthorised modifications to adapt large hole abrasive

wheels.

◆ Do not cut workpieces requiring a maximum depth of cut

exceeding that of the cutting disc.

◆ Do not use cutting discs for side grinding.

◆ Inspect grinding and cutting discs before each use. Do not

use chipped, cracked or otherwise defective discs.

◆ Ensure that the abrasive product is correctly mounted and

tightened before use and run the tool at no-load for 30 s

in a safe position, stop immediately if there is considerable

vibration or if other defects are detected. If this condition

occurs, check the machine to determine the cause.

◆ Ensure that blotters are used when they are provided with

the bonded abrasive product and when they are required.

◆ When applying a threaded hole disc, ensure that the

thread is long enough to accept the spindle length.

◆ Never use the tool without the guard.

◆ Check that the workpiece is properly supported.

◆ Do not exert side pressure on the grinding or cutting disc.

◆ Ensure that sparks resulting from use do not create a hazard

e.g. do not hit persons, or ignite flammable substances.

◆ Beware that after switching off the tool the wheel

continues to rotate for a short period.

◆ Ensure that ventilation slots are kept clear when working

in dusty conditions. If it should become necessary to clear

dust, first disconnect the tool from the mains supply.

Avoid damaging internal parts, use a soft brush or dry

cloth, do not use metallic objects.

◆ Abrasive wheels shall be stored and handled with care in

accordance with manufacturer’s instructions and always

store grinding and cutting discs in a dry place.

Features

This tool includes some or all of the following features.

1. On/off switch

2. Side handle

3. Spindle lock

4. Guard

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting and removing the guard (fig. A & B)

Fitting

◆ Place the tool on a table, with the spindle (5) facing up.

◆ Place the spring washer (6) over the spindle and locate it

on the shoulder (7).

◆ Place the guard (4) onto the tool as shown.

◆ Place the flange (8) over the spindle with the protruding

pips towards the guard. Make sure that the holes in the

flange align with the screw holes.

◆ Secure the flange with the screws (9). Make sure that the

screws are fully tight and that the guard can be rotated.

Removing

◆ Use a screwdriver to remove the screws (9).

◆ Remove the flange (8), guard (4) and spring washer (7).

Store these parts carefully.

Warning! Never use the tool without the guard.

Fitting the side handle

◆ Screw the side handle (2) into one of the mounting holes

in the tool.

Warning! Always use the side handle.

Fitting and removing grinding or cutting discs (fig. C - E)

Always use the correct type of disc for your application.

Always use discs with the correct diameter and bore size

(see technical data).

1 2 3 4 5 6 7 8 9 10 ... 63 64

Commentaires sur ces manuels

Pas de commentaire

Black & Decker KG725 Fiche technique Page 5

Commentaires sur ces manuels