Black & Decker GW370 Manuel d'utilisateur télécharger pdf (Page 10)

10

Using your product (Fig. J)

When using as a blower or vacuum, always

wear safety glasses. If using in dusty

conditions, wear a filter mask as well.

Switch off your product, allow the fan to

stop and remove the plug from the socket

before carrying out any adjustment,

servicing or maintenance.

Blow mode

J

• Attach the blow clamshell and tube

(6 & 7) to the powerhead (2) (Fig. J) by

locating the blower as indicated by

arrow 23, then pivot about this point

until the locking/release catch (24) is

fully engaged.

• Hold the blow tube approximately

180mm (7”) above the ground, switch

your product on and using a sweeping

motion from side to side, advance

slowly keeping the accumulated debris/

leaves in front of you (Fig. K).

• Once you have blown the debris/leaves

into a pile, you can convert to vacuum

mode to collect the debris.

Removing blow/vacuum tube (Fig. J)

J

• To disconnect the blow clamshell or

vacuum tube from the powerhead,

depress the release button (3), ensuring

the tube does not fall to the ground.

• The release button will not depress if

the switch is in the “on” position.

Vacuum mode (Fig. L - P)

To fit the bag assembly to your product:

(Fig. M, N, O)

• For vacuuming/shredding, the

collection bag (9) must be fitted to the

bag holder (8).

• Fig. M: Locate the bag rim (25) into the

bag holder channel (26) ensuring that

the front of the bag is placed over the

vacuum outlet (27).

• Slide the bag fully into the channel and

depress the latch (28) to lock the

handle into the bag top (Fig. N & O).

• Position the tube slightly above the

debris/leaves. Switch your product on,

then using a sweeping motion the

debris/leaves will be sucked up the

tube, shredded and thrown into the

collection bag (Fig. L).

• For stubborn debris/leaves your

vacuum tube is incorporated with a

scraper (13). Use this scraper to loosen

the debris and continue to vacuum as

normal.

• As the bag fills the power of the suction

will decrease, switch off your product

and unplug from the mains power supply.

• To remove the bag, depress the latch

(28) to disengage from the bag holder

and slide the bag out.

• To empty, hold the plastic handle (10)

and grab the nylon handle (29) on the

underside of the bag. Turn the bag

upside down and shake out any debris

and leaves.

Fault finding

Failure to operate (1) Check the connection to the

power supply.

(2) Check the fuse in the plug, if

blown, replace (UK only).

(3) Check that the blow/vacuum

tube assembly is correctly fitted

to the powerhead.

(4) If the fuse continues to blow -

immediately disconnect from the

mains power supply and consult

your local Black & Decker

authorised repair agent.

Poor vacuum/ (1) Switch off - disconnect from

high pitched whinethe mains power supply, debris

should fall clear of the tube.

(2) Remove and empty the

collection bag.

(3) Check that both the inlet and

exit ports on the vacuum tube

are clear.

(4) Remove any debris from the

fan area.

(5) If poor vacuuming continues -

immediately disconnect from the

mains power supply and consult

your local Black & Decker

authorised repair agent.

Poor shredding (1) Switch off - disconnect from

the mains power supply and

remove the collection bag.

(2) Remove the vacuum tube

and inspect the fan.

(3) Clean any debris from the fan

blades.

(4) If the fan is cracked or

damaged, do not use - consult

your local Black & Decker

authorised repair agent.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 59 60

Commentaires sur ces manuels

Pas de commentaire